DA Pam dated 1 July (supersedes DA Pam , dated 28 June in case you were wondering) is titled “The M16A1. : The M16A1 Rifle Operation And Preventative Maintenance DA Pam Original field manual illustrated by Will Eisner in comic form. SUMMARY of CHANGE. DA PAM –3. Soldiers’ Guide for Field Maintenance Operations. This major revision, dated 18 September
|Published (Last):||4 May 2014|
|PDF File Size:||15.47 Mb|
|ePub File Size:||12.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Too much lube speeds carbon buildup in the chamber and bolt locking recess. The cap’ll keep out rain, dust and dirt, but it won’t keep water from seeping into the bore from the chamber end when your rifle gets dunked. The one you save 7503-0 might save you some day.
Any stuflf that’s left after you do your level best won’t make no never-mind. No ”buts” about it. Then it’s due right now for a physical. Then dry the areas real good. Remove it from your weopon and fietd-strip it at least once a week. Sec- ond, he’s liable to let water seep into the lower receiver extension. Cleanliness is a must — and it may save your life! Sure, there’ re plenty of ’em in supply — world-wide — but they could get mighty scarce in your own sector.
When you’re oil through — and the lower receiver’s dry — put a generous coat of LSA FSN 9 on all of the insides of the tower receiver and on all of the parts. Of course, this all centers on remov- ing or not removing the components of the lower receiver to do the servicing job.
Next hit the forward assist and again pull the trigger.
Join the upper and Oam lower receivers. Which is A-OK as far as it goes. Then pull it back all the way out — again in short jerks. Just press the button on the right side of the rifle with the nose of a cartridge far enough so’s you can turn the catch on the left side of the weapon. Now you can understand why TM with Ch 1, does not authorize disassembly of the lower receiver group for cleaning by riflemen and armorers.
Get ’em and use’ em!
DA Pam : Free Download, Borrow, and Streaming : Internet Archive
Don’t worry about any discoloration you find there, though. A cleaning job like this will get rid of all the carbon and dirt that might keep your weapon from shooting right. This may not have anything directly to do with blowing up your shooter, but it could keep it from firing — which is the next worst thing. A rag or swab or even a pipe cleaner dampened with LSA will do the trick here.
Truth is, you are not authorized to remove the lower receiver’s parts at all. Choke up on the cleaning rod — hold it about 2 inches from the receiver and push it straight inch by inch in short jerks all the way through the flash suppressor. If you do, here’s what to look for: Slide out the floor plate. Just wiggle the spring into the mag as far as it’ll go.
Follow the guide on pages All components of the lower receiver — as well as the bolt carrier group — must wear a coat of LSA at all times. Maxie’s the best partner you’ll ever have.
Replace it if you find it damaged. This bolt has a great service record so tar, but it pays to be on the lookout for that first sign of weakness. In fact, with a rubber band closing — not to mention rips and tears — the bag’s not guaranteed watertight, so-oo-o. Don’t use wire, though, or you might scratch the tube and set up worse trouble later on.
Test the extractor spring by pressing on the extractor. The carrier key bends pretty easy — and then won’t line up inside the weapon. So, bear down on your bore brush in both these places. And still one more: They won’t match up with your authorized equipment.
Any further and you might damage it. The front end of the gas tube is self-cleaning, thanks to the hot gases and high pressure from the barrel. So get it off as quick as you can. You only use these new plastic protective caps FSN when you’re in action.
DA Pam 750-30
Quick-rip the bag off with one steady yank. Brackish water — that’s another story.
This could cause corrosion of the extension and rusting of the action spring — or it might result in a short recoil of the bolt carrier group, thereby preventing the bolt assembly from retraaing far enough to strip a cartridge from the magazine.
Here’s the easy way. You can see how it works by opening the receiver and turning the selector to AUTO and watching the movement of the tang of the 75-030 sear. This bag, y’know, won’t excuse you from regular PM chores.